Minka Lavery 1813-66 Manuál s instrukcemi stáhnout pdf

INSTALLATION INSTRUCTION FOR 1813-66/1813-84

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

ASSEMBLING THE FIXTURE (Fig. 1)

1. Carefully remove the fixture from the carton and check that

all parts are included as shown in the illustration.

2. Spread the arms (S) so that the arms (S) are at equal

distance from each other.

3. Thread the loop (J) onto the nipple (K). Tighten the loop

(J).

4. Thread the nut (M) onto the nipple (N), then thread the

nipple (N) into the coupling (L), and tighten with the nut

(M).

5. Slide the tube (O), cap (P) and washer (Q) over the nipple

(N), and secure with the nut (R).

Note: To avoid scratching the tube (o), spread the

arms(s) outward to a suitable position

6. Place the glass (U) over the socket (V), and secure in place

with retaining ring (T).

HANGING THE FIXTURE (Fig. 2)

7. Shut off the power at the circuit breaker and remove old

fixture from ceiling, including the mounting bar.

8. Thread the nipple (E) into screw collar (G) until snug.

9. Thread hex nut (D) onto nipple (E), insert lock washer (C),

thread the end of nipple (E), thread nipple (E) through

mounting bar (A), and continue until tight.

10. Take this mounting bar (A) assembly and mount to ceiling

junction box with junction box screws (B). Tighten screws

securely with screwdriver.

11. Using a pair of pliers to open the end of chain (I), and

connect it to the loop (J), and close it.(Fig. 1)

12. By measuring, determine correct number of links needed

for proper hanging height. Using the pliers, disconnect and

discard remaining chain.

13. Lace the fixture wires through the chain links. Slip screw

collar ring (H) over the chain, then do the same with the

canopy (F).

14. Open the other end of the chain (I) (provided) and connect it

to screw collar (G). Close the link.

15. Feed the fixture wires through the screw collar (G) and

nipple (E) and pull until taut.

CONNECTING THE WIRES (Fig. 3)

16. At this point, connect the electrical wires as shown in

(Fig. 3) making sure all wire nuts are secured. You may

have to wrap the connections with electrical tape. If your

outlet has a ground wire (green or bare copper) connect

fixture’s ground wire to it. Otherwise connect fixture’s

ground wire directly to the mounting bar (A) using the green

screw provided.

17. Tuck these wire connections neatly into the ceiling junction

box and then raise the canopy (F) all the way to the ceiling.

Raise the screw collar ring (H) and thread onto screw collar

(G) protruding through canopy (Fig.2)

18. Install the light bulbs in accordance with the fixture’s

specification.

DO NOT EXCEED THE MAXIMUM WATTAGE RATING!

Your installation is now complete. Return power to the

junction box and test the fixture.

Fig.2

Fig.1

Shrnutí obsahu

Strany 1

INSTALLATION INSTRUCTION FOR 1813-66/1813-84 WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER. ASSEMBLING THE FIXTURE (Fig. 1) 1.

Komentáře k této Příručce

Žádné komentáře

Minka Lavery 1813-66 Manuál s instrukcemi

Procházejte online nebo si stáhněte Manuál s instrukcemi pro ne Minka Lavery 1813-66. Minka Lavery 1813-66 Instructions / Assembly Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro ne Minka Lavery 1813-66